voltage 200 to 1000 v current 5.0 a jun - 08 vf max. instantaneous forward voltage @ 2.5 a ir maximum dc reverse current @ t c = 25 oc at rated dc blocking voltage @ t c = 125 oc rthj-c typical thermal resistance (note 1) 4.0 c/w maximum recurrent peak reverse voltage (v) maximum rms voltage (v) maximum dc blocking voltage (v) maximum average forward rectified current see fig. vrrm vrms vdc i f(av) tj,tstg operating and storage temperature range ifsm peak forward surge current 8.3 ms. single half sine-wave superimposed on rated load (jedec method) 5.0 a 30 a ? 65 to + 150 c 200 800 140 560 200 800 cj 5.0 a 100 a frf 503g frf503g ........ frf507g absolute maximum ratings, according to iec publication no. 134 isolated 5.0 amp. glass passivated fast recovery rectifiers ito-220ab 1 3 400 280 400 1000 700 1000 frf 504g frf 506g frf 507g 1.5 v 150 ns maximum reverse recovery time from i f =0.5 a; ir = 1 a; irr = 0.25 a t rr typical junction capacitance at 1mhz and reverse voltage of 4v dc 500 ns 140 pf note: 1. thermal resistance from junction to case per leg mounted on heatsink size of 50.8 mm x 76.2 mm x 6.35 mm al-plate. electrical characteristics 600 420 600 frf 505g frf 503g frf 504g frf 506g frf 507g frf 505g ?? glass passivated chip junction. ??low power loss mechanical data ??terminals: pure tin plated, lead free. leads solderable per mil-std-202, method 208 guaranteed ?? high current capability ?? case: ito-220ab molded plastic ??polarity: as marked ??mounting position: any ??weight: 2.24 gram s ??e poxy: ul 94v- 0 rate flame retardant ?? high efficiency, low vf ?? high reliability ?? high surge current capability ??h igh temperature soldering guaranteed: 260 c/10 seconds/6.35mm from case. 250 ns ??mounting torque: 5 in - 1bs. max. 2 pin 1 pin 3 pin 2
jun - 08 frf503g ........ frf507g 0.01 i f , instantaneous forward current (a) 0.2 v f , instantaneous forward voltage (v) 0.8 1.0 1.2 typical forward characteristics per leg 8.0 100 maximum non-repetitive forward surge current per leg 30 0 10 1 ifsm , peak forward surge current (a) 300 0 50 0.1 cj, junction capacitance (pf) percent of rated peak reverse voltage (%) ir , instantaneous reverse current (a) 0 0.1 1000 1000 0.9 1.1 typical reverse characteristics per leg 20 40 60 80 number of cycles at 60 hz typical junction capacitance per leg vr , reverse voltage (v) 10 140 5 tl , lead temperature (c) 0 i f(av) , average forward current (a) 100 5 0 maximum forward current derating curve 150 50 1.3 1.4 250 reverse recovery time characteristic and test circuit diagram non inductive 50w pulse generator (note 2) set time base for 5/ 10ns/ cm 1cm trr +0.5a 0 -0.25a -1.0a 1w noninductive dut oscilloscope (note 1) non inductive 10w (+) 50vdc (approx) (-) (+) (-) notes: 1. rise time = 7ns max. input impedance = 1 megohm 22 pf 2. rise time = 10 ns max. sourse impedance = 50 ohms 3 0.04 200 50 0.5 1 10 100 25 20 5 2 5 20 50 120 100 2 4 1 1 0.02 0.4 4.0 15 150 100 2.0 500 10 1.0 0.1 1.5 100 rating and characteristic curves tj = 25 c pulse width = 300 s 1% duty cycle 8.3ms single half sine wawe jedec method tj = 125 c tj = 25 c tj = 25 c f = 1.0 mhz vsig = 50m vp-p
frf5g jun - 08 isolated 5.0 amp. glass passivated fast recovery rectifiers package mechanical data ito-220ab dimensions a b c e f1 f2 l2 l3 l4 l5 milimeters - 2.5 - - 13.2 14.8 2.55 - - - - - - - - - nominal min. - - ref. - l7 6.3 - d - - - f - - dia 3.0 - g1 - 2.55 4.7 2.8 13.8 15.5 2.85 4.1 3.16 max. 0.76 1.4 6.9 1.8 10.3 0.9 3.4 -
|
